My buddies YFZ508 Falicon stroker

Message
Author
azcannibal
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

My buddies YFZ508 Falicon stroker

#1 Post by azcannibal »

The YFZ picture is my buddies check out the spacer below the cylinder can you say "STROKED"?.....he stroked it with a Falicon crank setup....now it's a 508cc....I think I'll be just watching him from afar on my Cannibal.....OK at least till I get mine broken in.....(1 Tank of Gas should do it) then I'll keep my distance as he goes by me.



Later!

haydug
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

#2 Post by haydug »

hmmm, guess I'm not the only one to want more out of the yammie!! smile.gif
Give us a report.

azcannibal
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

#3 Post by azcannibal »

Leaving in the morning!

Sandstorm
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

#4 Post by Sandstorm »

I have seen this YFZ run personally. It is wicked fast. It is under 300lbs. This is one of the best vids I have ever seen. The racing is near the end of the vid, but it's a must see vid all the way through.. It is Utah's Sand Mtn and Made by CPCPatriot..

http://www.planetsand.com/ubbthreads/showf...rt=1#Post252887

azcannibal
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

FAST !!!

#5 Post by azcannibal »

Thanks for the Video....keep them coming....!

Going to Buttercup in the morning!!

Got to break in my 450 before I go up against the 508cc.

Looks like I should get a dust mask! LOLs

L8R

JST
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

#6 Post by JST »

Who built the 508?

azcannibal
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

#7 Post by azcannibal »

Haydug is doing some I think ....it is a falicon kit.

cannibalq8
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

#8 Post by cannibalq8 »

Falicon stroker/bore kit is ...
( 97mm ) 460bb piston kit + DD05 4mm stroker = 488c.c

Ma_ Po___ stroker/bore kit is..
( 99mm ) 480bb piston kit + DD05 4mm stroker = 508c.c

which i think ur friend and Doggriders use them.

The reason is that Falicon use (97mm ) 460bb piston kit here is that they think that going over that bore will use useless and wont gain more power.

azcannibal
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

Results

#9 Post by azcannibal »

Been busy. Sorry for not replying in a while....the 508 dominated everything on the hill. He let me ride it. It is very controllable with the 6" over swing arm. To much $$$ for me to even say I'm going about to go that route....I am very pleased with the way my Cannibal runs...

cannibalq8
Posts: 0
Joined: Wed Mar 10, 2021 10:41 pm

#10 Post by cannibalq8 »

hey azcannibal

could u tell us more details about how ur DR450 doing against Yfz508? .. coz my friend yfz looking for same ur friend 508 kit?

thanx

Post Reply