Durablue axle question
Posted: Wed Apr 14, 2004 3:02 am
Im buyin a durablue 2+2 axle from thomez:D , will my stock sprocket hub and everything else fit onto the axle??thanks alot
Matt....
Matt....
Cannondaleriders
A safe place for quads older than the owners
https://cannondaleriders.com/phpbb/
Durablue axle question
https://cannondaleriders.com/phpbb/viewtopic.php?f=16&t=5080
Page 1 of 1
Posted: Wed Apr 14, 2004 4:05 am
The sprocket should it will on the lsr everything else will. Man zack you can move some parts, I heard about that axle last night and its already sold.
Posted: Wed Apr 14, 2004 4:12 am
how do i take off the sprocket hub from the stock axle?, Zack is an awsome person to deal with:clap:
Posted: Wed Apr 14, 2004 5:01 am
pretty sure you take it and press it inwards then slide the c clip out with a screw driver ( more like pry it out) then slide the hub off, thats how mine came off anyway, but it was stripped out..you may need to use a presss, or just buy a sprocket hub for them, they should make em for their x-33 axle
Posted: Wed Apr 14, 2004 11:32 pm
I have a durablue and all the stock stuff worked on it.
I got my hub off just like CdaleRacer0128 did. Gently tapped it towards the center of the axle with a rubber hammer and removed the clip. Then worked it off the axle. Mine came off just fine without using a press and at the time the quad was only about a month and a half old with about 10 hours on it.
I will say that I did have one problem after I installed it. I could not keep the axle lock nut tight. It would come loose about about 10 minutes of ride time. So I bought a LSR lock nut and haven't had any problems since.
I got my hub off just like CdaleRacer0128 did. Gently tapped it towards the center of the axle with a rubber hammer and removed the clip. Then worked it off the axle. Mine came off just fine without using a press and at the time the quad was only about a month and a half old with about 10 hours on it.
I will say that I did have one problem after I installed it. I could not keep the axle lock nut tight. It would come loose about about 10 minutes of ride time. So I bought a LSR lock nut and haven't had any problems since.
Posted: Thu Apr 15, 2004 1:04 am
Well aren't you cool Brad!
lol So, what Nat. are you going to next bud?:usa
lol So, what Nat. are you going to next bud?:usaPosted: Thu Apr 15, 2004 1:45 am
Ok Brian, 
I don't think I will be going to any more nationals this year. Not enough time or money. I guess I will just stick to what local races I can make and see how that comes out.
I don't think I will be going to any more nationals this year. Not enough time or money. I guess I will just stick to what local races I can make and see how that comes out.
Posted: Thu Apr 15, 2004 2:22 am
That's cool. Be safe and good luck. Keep an eye on those terminal screws! 
Later.
Later.Posted: Fri Apr 16, 2004 10:56 pm
whats a terminal screw? anyways, i got the clip off the sprocket hub which way does it come off towards the wheel hub? or torwards the inside then off the side the rotor hub comes off, mine wont come off, grrrrrr
Posted: Fri Apr 16, 2004 11:06 pm
A rubber mallet or a mallet and a piece of wood and slowly work it towards the wheel hub side's. It may be on tight, but that's a good thing. Take your time and they'll come off.