02 cdale 440 starting hard?? need help guys
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
I have a 02 cannondale 440, and i just got it about 4 months ago. It was supposed to have all updates done and only 15hrs on motor, but he had no paper work on that. When i got it, it started fine, a little slow cranking but it still started and ran fine. After riding it for awhile the idle got irratic and i noticed the idle screw was moving around on me as i rode or reved it. Now it will start, but i must fool with the idle screw to get it going, and it cranks over hard and very slow to get it to fire. And it also has a hesitation off idle when riding. I have read that i need to get the d&m kit to fix this, but i am lost when it comes to these cdales, i have only had yfz450s and 450r's. lol Id love to get this thing going as soon as possible, it is a super clean quad and i am in love with it already. ANY help would be great guys! thanks!
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE (dayton02cdale @ Nov 5 2011, 05:36 PM) <{POST_SNAPBACK}>
I have a 02 cannondale 440, and i just got it about 4 months ago. It was supposed to have all updates done and only 15hrs on motor, but he had no paper work on that. When i got it, it started fine, a little slow cranking but it still started and ran fine. After riding it for awhile the idle got irratic and i noticed the idle screw was moving around on me as i rode or reved it. Now it will start, but i must fool with the idle screw to get it going, and it cranks over hard and very slow to get it to fire. And it also has a hesitation off idle when riding. I have read that i need to get the d&m kit to fix this, but i am lost when it comes to these cdales, i have only had yfz450s and 450r's. lol Id love to get this thing going as soon as possible, it is a super clean quad and i am in love with it already. ANY help would be great guys! thanks!
were are u out of .....if ur in dayton ohio I can help I have a d&m....
Maybe you just have the idle set to low. Dales idle at 2100 rpm so it wont thump thump thump like a 400ex. Also check your battery put a voltmeter and measure voltage while cranking. If its lower than 10 volts it will crank to slow for quick starting.
Are you also doing the cold start procedure? Tap the start button 3 times in ten seconds but not long enough to actually crank the engine over. Then do a full crank and it should fire on the first revolution. Just cranking the crap out of them is not how to start them cold. You shouldnt be touching the throttle either until it fires .
Are you also doing the cold start procedure? Tap the start button 3 times in ten seconds but not long enough to actually crank the engine over. Then do a full crank and it should fire on the first revolution. Just cranking the crap out of them is not how to start them cold. You shouldnt be touching the throttle either until it fires .
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE (beanie$440$peed @ Nov 5 2011, 01:07 PM) <{POST_SNAPBACK}>
were are u out of .....if ur in dayton ohio I can help I have a d&m....
I am in Vandalia, ohio. Like 15 minutes north of downtown. That would be sweet, any help is appreciated seeing as i know almost nothing about these quads.
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE (Wistech @ Nov 5 2011, 06:00 PM) <{POST_SNAPBACK}>
Maybe you just have the idle set to low. Dales idle at 2100 rpm so it wont thump thump thump like a 400ex. Also check your battery put a voltmeter and measure voltage while cranking. If its lower than 10 volts it will crank to slow for quick starting.
Are you also doing the cold start procedure? Tap the start button 3 times in ten seconds but not long enough to actually crank the engine over. Then do a full crank and it should fire on the first revolution. Just cranking the crap out of them is not how to start them cold. You shouldnt be touching the throttle either until it fires .
Are you also doing the cold start procedure? Tap the start button 3 times in ten seconds but not long enough to actually crank the engine over. Then do a full crank and it should fire on the first revolution. Just cranking the crap out of them is not how to start them cold. You shouldnt be touching the throttle either until it fires .
Yeah i have been doing the cold start procedure. And yeah the battery was the first thing i looked at and it definitely is low. I just think there is something other than that wrong since it acts like it doesn't want to hit, and once it is warm it is nearly impossible to get started. And i didn't know the idle was set so high on them, i feel like that could definitely be a possibility. thanks!
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE (dayton02cdale @ Nov 5 2011, 11:03 PM) <{POST_SNAPBACK}>
Yeah i have been doing the cold start procedure. And yeah the battery was the first thing i looked at and it definitely is low. I just think there is something other than that wrong since it acts like it doesn't want to hit, and once it is warm it is nearly impossible to get started. And i didn't know the idle was set so high on them, i feel like that could definitely be a possibility. thanks!
yup give me a call 5595646 our area code
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
I got the quad going! thanks guys! And HUGE thanks goes out to Roxygirl, he helped me out a ton and got me all squared away. I took the quad to him and he went out of his way to get me going before i left and he had to go to work a 12 hour shift. Great guy in my book! and thanks to beanie440 for hooking me up with him.