MAPS

Message

timbomoose · #1 Post by **timbomoose** » Mon Nov 06, 2006 2:47 am

1st map extreme is used for ported 2.2mm strokers with airbox. Parameters for 448cc(95mm piston) 2360 1.05 offset 467cc (97mm piston) 2300flowrate 1.1 offset.
4th map the LAFEMM is a softer map for the same setup.

2nd map terminator is for an open airbox setup (example cannonboomer or cyclone pod filter) for 2.2mm ported strokers .Parameters for 448cc (95mm piston) 2330 flowrate 1.05 offset for 467 (97mm piston) 2275 flowrate 1.1 offset.

3rd map exterminator2.THIS IS ONLY FOR HARLEY INJECTORS!!!!Map is made for 495cc or 505cc ported open air set 67mm stroke.495 cc 2620 offset .88 505cc 2560 .88.Running this map with stock injectors can be damaging!

These maps are all from gen3 porting made with factory fmf ti pipes 93 octane gas.
extreme 448cc 49.5hp 467cc 52 hp
terminator 448cc 52 hp 467cc 55 hp
exterminator2 495cc 58.5 505cc 60 hp
Dyno hp at atv rear wheels hoosier tires rounded off to the nearest .5 hp.

All settings are ROUND ABOUT. Fuel pressure and injector flow varies from machine to machine which will cause differences in settings.Pipes and cam timing will also affect maps!Go rich then to lean for adjusting.If running hot richen up and/or run better gas.

timbomoose · #2 Post by **timbomoose** » Mon Nov 06, 2006 3:04 am

Extreme & terminator map have 10850 rev limiter and exterminator2 map 10500.

Sandstorm · #3 Post by **Sandstorm** » Mon Nov 06, 2006 4:03 am

Tim how is the Terminator map different from Animals map??

timbomoose · #4 Post by **timbomoose** » Mon Nov 06, 2006 4:35 am

Its leaner bottom end and richer in other areas.Timing very close.Animals was made for closed air box terminator open. I'm sure ******, my personal map analyzer, will have a break down for you. Seems as I'm typing he's downloading the maps. I'm glad I give this lost,bored individual a purpose in life.

fig · #5 Post by **fig** » Mon Nov 06, 2006 5:38 pm

Thanks for the help/map Timbo.

jesshamner · #6 Post by **jesshamner** » Mon Nov 06, 2006 8:56 pm

I have been looking for maps to use. I have your stroker crank, hmf slipon/02 header, stock airbox, stock piston, and no porting. Should I be sticking to the stock maps or are there other maps that I could use?

cannondale27 · #7 Post by **cannondale27** » Tue Nov 07, 2006 1:42 am

Run stock maps with that combo.Motospeed,Blazespeed or just stock.

jesshamner · #8 Post by **jesshamner** » Tue Nov 07, 2006 2:04 am

Animals128 too rich?

wistech · #9 Post by **wistech** » Tue Nov 07, 2006 2:24 am

The animal128 is for a ported head. Yours is close enough to stock to run stock mmaps.

jesshamner · #10 Post by **jesshamner** » Tue Nov 07, 2006 2:33 am

What about the x440s/Speed map? I have tried it and the Animals128. Both run good except the x440s/Speed has a dead spot in the mid range. The Animals128 screams throughout but I can tell its too rich.