Problem with iPaq
Problem with iPaq
I have a iPaq 3835 with the D&M kit installed. It reads that it is connected correctly but I can only receive info from the ECU. When I send Info it says that it is communicating but no info is being sent. It just stays in that mode won't cancel or anything.
The D&M kit on my PC works great but I would like to use my iPaq.
Anyone else have this problem with their iPaq?
Terry
03 MOTO
The D&M kit on my PC works great but I would like to use my iPaq.
Anyone else have this problem with their iPaq?
Terry
03 MOTO
I haven't got one of those little hand held thingies yet, but...
Sometimes when either of the battery voltages, quad or iPaq, is low it will take a long time to download.
Did you make sure that you re-powered the ecu before hitting the send button?
When sending files to the ecu, can you see the progress in the upper right hand of the screen? If you can see the bar graph moving, then you are communicating. If you get the words "retrying checksum", then you have a small problem with communication.
I hope it all goes well, if not you may have to give scooter at optimum a call and he'll run you through it.
Good luck.
Sometimes when either of the battery voltages, quad or iPaq, is low it will take a long time to download.
Did you make sure that you re-powered the ecu before hitting the send button?
When sending files to the ecu, can you see the progress in the upper right hand of the screen? If you can see the bar graph moving, then you are communicating. If you get the words "retrying checksum", then you have a small problem with communication.
I hope it all goes well, if not you may have to give scooter at optimum a call and he'll run you through it.
Good luck.
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE
Originally posted by ronnoc47
EuroGOD, I tried everything that you mentioned. The graph bar was there but wasn't moving. I'll probably give Scooter a shout.
Thanks!
Terry
03 MOTO
EuroGOD, I tried everything that you mentioned. The graph bar was there but wasn't moving. I'll probably give Scooter a shout.
Thanks!
Terry
03 MOTO
Mine does the same thing, haven't had time to call that dude yet though. I have a 2200 btw, if you figure it out PLEASE post up!
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE
Originally posted by ronnoc47
EuroGOD, I tried everything that you mentioned. The graph bar was there but wasn't moving. I'll probably give Scooter a shout.
Thanks!
Terry
03 MOTO
EuroGOD, I tried everything that you mentioned. The graph bar was there but wasn't moving. I'll probably give Scooter a shout.
Thanks!
Terry
03 MOTO
That shows that you've got a connection, what is the led on the comms cable doing? Is is lit, flashing or out?
Whenever the download/upload takes longer than usual, I would suggest a weak battery voltage. What does the voltage show on the D&M program? Anything over 12.5 volts is good.
I had a laptop that would upload in under 30 seconds, download would sometimes take over 5 minutes....turned out the battery pack for the laptop wasn't holding a charge.
Disconnecting the computer during a download can corrupt the hex code as well.
Check your voltage, re-load the hex if necessary and tell us how it goes.
I still can't get the iPaq to work. Like EuroGOD said it messes up the hex code or something when I disconnect it because it won't download properly. Then I have to use a desktop to reprogram in my stock settings. My battery on the quad is fully charged and the coms light is on and I have the iPaq plugged into a external power source with all programs closed except the d&m program. Still no luck. If anyone has used the iPaq to download maps, please let me know what the secret is to make it work. I'm starting to think that maybe the iPaq processor is to slow. The desktop works awsome but I bought the iPaq so I could change maps at the track.
Terry
03 MOTO
Terry
03 MOTO
iPaq update. Finally got it to work! works great now. Much more convenient than hooking it up to the table top pc. Problem was that I had to download a updated softpaq software to my iPaq. Found out about it on the HP / Compaq website. The d&m kit software was not the problem. Now I can look forward to my hair growing back!
Terry
03 Moto
Terry
03 Moto