left side drive conversion
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
hey guys,
ok so ive got a little project on the go, but im still waiting on all my parts from moto44 before i can start it.
but here is the general gist of what im planning.
i want to fit a trx250r motor into a dale frame, this should be pretty easy the only problem im having is changing the dale drive from right to left. i was thinking, these are my problems:
will a 250r bearing carrier fit in our dale swing arm???
can i just slide the standard carrier into the swingarm the opposite side so the drive sprocket is on the left side??
if none of these work i was thinking of swapping out the whole swinger for a trx250r "no link" one this should solve my problem.
does anybody have any things they no that could help out on this, any help would be awesome!!
sorry guys to be a pain in the butt, once both my bikes are built i mite finally get to ride!!!!
ha ha ha
cheers guys
Jay
ok so ive got a little project on the go, but im still waiting on all my parts from moto44 before i can start it.
but here is the general gist of what im planning.
i want to fit a trx250r motor into a dale frame, this should be pretty easy the only problem im having is changing the dale drive from right to left. i was thinking, these are my problems:
will a 250r bearing carrier fit in our dale swing arm???
can i just slide the standard carrier into the swingarm the opposite side so the drive sprocket is on the left side??
if none of these work i was thinking of swapping out the whole swinger for a trx250r "no link" one this should solve my problem.
does anybody have any things they no that could help out on this, any help would be awesome!!
sorry guys to be a pain in the butt, once both my bikes are built i mite finally get to ride!!!!
ha ha ha
cheers guys
Jay
http://www.exriders.com/vbb/showthread.php...250r+conversion
This might help.
Personally I would use something with a little more power than a little 250cc honda. A 500 cc 2 stroke would be more apropriate.
This might help.
Personally I would use something with a little more power than a little 250cc honda. A 500 cc 2 stroke would be more apropriate.
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
I have two trinity 421 pv motors sitting in my garage, I'm going to try and get one in the frame once I work out how to swap the drive over, wiuld it be easier to just drop the swinger off and putt a extended banshee one on rather than mod the Dale one???
Once I get all my parts over from Morgan I'll see how it fits in
Once I get all my parts over from Morgan I'll see how it fits in
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE (cannondale27 @ Dec 8 2010, 04:30 PM) <{POST_SNAPBACK}>
Its pretty easy to use the dale one.Just need to weld a bung on for brake stay and move everything from left to right.Banshee would be cool.Sky is limit with power out of them.Pipes would be a nightmare though.Unless you ran them underneath like a bike.
There might be more room there than you think, no battery for starters, and you can kiss goodbye to the ecu tray etc, though the fuel tank/carbs/air filters going to be a pain....
Almost sounds like a bit of a challenge......
I'll stick to what I know for now, which isn't much!
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
ill put one in as a mock up and take some pics of it, i think the carbs will be fine as the motor doesnt mount from the swing arm, so you can push the motor forward a few inches for clearance. and the carbs sit ontop of the motor and only protrude out the back a couple of centimeters. it will be an animal, my mate is a banshee man, hees got a triple in one of his bikes and that thing is scary fast!!!!!
took it to santa pod and it beat a turbo busa hands down!!! ha ha ha, cost almost 18k to build tho!!!!
lucky his dad is a millionaire really.
took it to santa pod and it beat a turbo busa hands down!!! ha ha ha, cost almost 18k to build tho!!!!
lucky his dad is a millionaire really.
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm