Parts FAQ

Message

Jaybr · #1 Post by **Jaybr** » Tue Mar 29, 2005 5:18 pm

Most any part you need for your Cannondale is available through one of our site sponsors, all stock replacement parts for sure. Please call them first.

Please add to this list. It will be updated and just facts edited and added to list. To make it easy to read. Thanks for contributing.

This is a comprehensive list of what's available in aftermarket.

Updated List

CODE

[list]

[*]Air Filter     ????K&N, Twin Air, No Toil, Uni

[*]A-arms ???? ????Houser, Gibson, LSR, American Star, Walsh Racecraft, Eyeball, Herman, Action Racing

[*]Axles ???? ????RPM. Lonestar, Durablue, RAD

[*]Balance shafts     ????[email]sales@hanovergear.com[/email]

[*]Bearing Carriers ????RAD

[*]Brake Calipers     ????same as DS650?

[*]Brake Lines     ????Galfer

[*]Brake Rotors     ????Hardkor, RAD. Stock DS650

[*]Brake Pads (front) ????EBC FA121

[*]Brake Pads (rear) ????EBC FA181

[*]Bumper ???? ????AC, PRM, Graydon

[*]Chain ???? ????520 O-Ring 96 Links

[*]Chain Roller     ????Honda 98-2001 CR250

[*]Clutch Cover     ????RIS

[*]Clutch baskets ???? ????(outer) Sponsors[email]sales@hanovergear.com[/email], R&S Performance

[*]Clutch packs     ????Sponsors

[*]ECU ???? ????Sponsors, Optimum Power

[*]Engine Mount update ????Quadsource,R&S Performance

[*]Engine Stud update ????Quadsource, Stage 8

[*]Engine side cover gasket    Cometic

[*]Exhaust (headpipes) ????HMF, Trinity, South Bay Moto, TC Racing, Graydon

[*]Exhaust (silencers) ????HMF, Trinity, Big Gun, TC Racing. Graydon

[*]Exhaust (crush washer) ????Honda TRX90

[*]Flywheel Puller     ????KTM
???? ???? ????Steahlyoffroad.com at 1-800-800-2363 the puller stock no. is "E-12".

[*]Fuel Filter ???? ????WIX 3011, NAPA Gold 3011

[*]Fuel Pump     ????Sponsors, Optimum Power

[*]Gas Cap ???? ????RIS, 01 cr250, crf50

[*]Kill Switch     ????Pingle

[*]Kill switch plate ????Arens, Speed2424

[*]Hoods ???? ????Quadtech

[*]Hubs ???? ????Hardkor

[*]Nerf Bars     ????AC, Graydon

[*]Oil Filters (paper) ????   Sponsors

[*]Oil Filter (stainless) ????Scotts, Dual Star, [url]http://www.americandirtbike.com[/url]

[*]Oil Filter Cover ????      RIS

[*]Piston ???? ????                 Timbomoose, Black Widow ATV, Caniboomer, Peterock

[*]Plastic ???? ????                Cyra, Fullbore

[*]Radiator Scoops     ????OMF, PC Products

[*]Seat Covers     ????[url]www.atvseatcovers.com,[/url] Nacs, Quadtech, Guts

[*]Shocks ???? ????               Elka, Axis, PEP, Ohlins,TCS, Works

[*]Skid Plates     ????PRM, Graydon, UM

[*]Sprocket (front) ????    Sprocket Specialist, KTM

[*]Sprocket (rear)     ????Honda 250r or 400ex

[*]Starter gears     ????Sponsors, [email]sales@hanovergear.com[/email]

[*]Stator Cover     ????RIS

[*]Steering Dampers ????Scotts, Ohlins, Denton

[*]Steering Stems     ????Arens, Houser, Desert Toyz, Herman

[*]Swingarms     ????Walsh Racecraft; Lonestar, Herman

[*]Tie Rods     ????RetroZ (forum member)

[*]Tie Rod boots     ????Quadshop

[*]Tie Rod Ends     ????Black Widow ATV, RetroZ (forum member)

[*]Timing gears     ????Sponsors, [email]sales@hanovergear.com[/email]

[*]Tools (specialty) ????SPX 1-800-328-6657

[*]Trans Bearings     ????SKF 6004 2zjem ball brg.
????     ????SKF nu205 ecp cyl. roll brg.
????     ????FAFNIR 205kg ball brg.
????     ????Consolidated 6004 zznr

[*]Trans gears or shafts ????[email]sales@hanovergear.com[/email]

[*]Trans close ratio gears ????Sponsors, R&S Performance

[*]Wheels ???? ????ITP, Douglas, Hiper (Honda pattern, 4/1 offset)

[*]6-pack rack     ????PRM (400 ex), Quadshop

[*]Camshaft bearings ????Consolidated#61805{large one]????Consolidated#RNA-4901[small one]

[*]OEM Stator     ????Black Widow ATV, ATK

[*]fuel pump relay     ????

[*]Diamond Racing     ????swingarm bearing kits (better than stock)
???? ????steering stem bearing retainer (billet)

[*]front hubs     ????400EX

[*]front rotors     ????400EX

[*]front brake calipers ????DS650

[*]rear axle bearings ????250R

[*]front spindles     ????400EX (must use stock inside spacer from honda)

[*]if you run LSR arm on the front, DON'T buy replacment parts from them.
here's a little info I found surprising. Upper A-arm rod end LSR retail 23 bux!
Summit racing retail $5.95!! 1/2 inch right hand thread (male)
tie rod ends LSR retail 26 bux! Summmit racing retail $7.95!
1/2 inch right hand, left hand thread (female) ball joints LSR retail 26 bux!
Parts store $14.95 GM truck tie rod end!! he he he

[/list]

CannondaleRider · #2 Post by **CannondaleRider** » Sun Jun 05, 2005 4:43 am

I didn't know 400EX hubs work? Can someone reassure this

And the CR250 chain rollers fit, now this is the upper AND lower rollers right?

CannondaleRider · #3 Post by **CannondaleRider** » Fri Jul 08, 2005 7:35 pm

The list says 400EX front hubs work. Nothing about rear.

krash "installed" some 400EX rear hubs on a stock Dale axle......with lots of force. Now they won't come off. I could run it with no castle nut with no worries:eek:

I haven't put heat to it yet, but as of now, i'll have to cut something. So i'm not sure about 400EX hubs

Exodus · #4 Post by **Exodus** » Sat Jul 09, 2005 3:37 am

Yeah its the same going the other way to, Can to honda, they take some beating. Colby stripped out a pair of Cannondale hubs on the back of his 450r last year, so they might not be the best choice. The number of splines are the same, the spline spacing is just a touch off.

CannondaleRider · #5 Post by **CannondaleRider** » Mon Jul 11, 2005 6:06 am

Yeah, kinda sucks.

so does anyone know if the fronts work