Page 1 of 1
Posted: Sat Dec 22, 2007 4:55 pm
by 2000ex
I have been in the garage all morning cooking up a few sets of freshly powdercoated Walsh A-Arms. I used to do some PC work on the side for others, but NOW I remember why I hated doing it. Girlfriend was complaining about the smell too
![rolleyes.gif](http://www.cannondaleriders.com/forums/style_emoticons/<#EMO_DIR#>/rolleyes.gif)
I told her these are much better than her co-workers christmas cookies
![smile.gif](http://www.cannondaleriders.com/forums/style_emoticons/<#EMO_DIR#>/smile.gif)
These will be going on my matching race and practice bikes for 2008
Pics will come as soon as they cool down.
On a side note I found a source of the teflon lined spherical bearings that are over HALF the cost Walsh charges. They want $20 each..x 8 = $160
![ohmy.gif](http://www.cannondaleriders.com/forums/style_emoticons/<#EMO_DIR#>/ohmy.gif)
Picked up 8 for under $60. If someone wants to know the part numbers I will be more than happy to share.
Posted: Sun Dec 23, 2007 4:15 am
by speed2424
I may have to replace mine next year, let me know what the numbers are. Thanks.
Posted: Sun Dec 23, 2007 7:52 am
by 311racer
Me too, pm me the numbers also.
thanks,mike
Posted: Sun Dec 23, 2007 2:12 pm
by 2000ex
Mike, did you ever get those to fit?
The part number is COM12T. Try sourcing them at your local bearing shop for less but online they are about $9-10/each.
Posted: Tue Dec 25, 2007 5:30 pm
by 2000ex
Hope this PEP rear is all it is cracked up to be
![tongue.gif](http://www.cannondaleriders.com/forums/style_emoticons/<#EMO_DIR#>/tongue.gif)
Posted: Tue Dec 25, 2007 5:33 pm
by 2000ex
The Evol bike will be my race machine, the moto ohlins machine will be a sort of replica Nacs Moto. Once these are done I need to get crackin on the other two
[attachment=5240:08_Canno...ilds_003.jpg]
[attachment=5238:08_Canno...ilds_005.jpg]
Looks like a slight camber adjustment is in order
[attachment=5239:08_Canno...ilds_002.jpg]
Posted: Tue Dec 25, 2007 5:35 pm
by 2000ex
Timbo Unicorn Stroker 467 and Falicon 468.
I have never run the Falicon and after Tim's pics of the crank pin it kind of has me worried
![dry.gif](http://www.cannondaleriders.com/forums/style_emoticons/<#EMO_DIR#>/dry.gif)
The Falicon bike will not see much use.
[attachment=5241:08_Canno...ilds_004.jpg]
Posted: Wed Dec 26, 2007 2:57 am
by 311racer
Mike, did you ever get those to fit?
The part number is COM12T. Try sourcing them at your local bearing shop for less but online they are about $9-10/each.
Yes, I did. Come to find out I have honda upper arms and I had to switch to honda spindles and hubs. I had to get the elka bodies shortened to the length. But now everything is good now. I hope!!!!
Thanks for the part #, My I wish I could afford the fox shocks.
Posted: Wed Dec 26, 2007 3:27 am
by 311racer
On a side note I found a source of the teflon lined spherical bearings that are over HALF the cost Walsh charges. They want $20 each..x 8 = $160
![ohmy.gif](http://www.cannondaleriders.com/forums/style_emoticons/<#EMO_DIR#>/ohmy.gif)
Picked up 8 for under $60. If someone wants to know the part numbers I will be more than happy to share.
[/quote]
Have you found a source for the upper and lower heim ends. I know the uppers are 7/16 and the lowers are 1/2.
Mike
Posted: Wed Dec 26, 2007 9:38 pm
by 2000ex