Page 1 of 2
Wheel Spacers
Posted: Tue Mar 15, 2005 8:56 pm
by KRMit
I was thinking about getting some wheel spacers for the rear as opposed to a wider axle. Any ups or downs to this? Also, which bike would I have to order them for?
Posted: Tue Mar 15, 2005 9:15 pm
by cdsracer
I've had the Durablue 2" spacers on the rear of my '02 Cannibal for about a year and a half now. They are extremely light and don't look too bad. They have a lifetime warranty and are fairly inexpensive. Handling is much improved especially in sand. I just broke my second one though, and I'm looking for an axle. My advice is to just go for an axle.
Posted: Tue Mar 15, 2005 9:17 pm
by KRMit
QUOTE
Originally posted by cdsracer
I've had the Durablue 2" spacers on the rear of my '02 Cannibal for about a year and a half now. They are extremely light and don't look too bad. They have a lifetime warranty and are fairly inexpensive. Handling is much improved especially in sand. I just broke my second one though, and I'm looking for an axle. My advice is to just go for an axle.
Well, I was looking at the GForce aluminum spacers. I wouldn't think they would break as easy as the others.
Posted: Tue Mar 15, 2005 9:37 pm
by acarli3
I had some wheel spacers on my quad until a I forgot to tighten down the lug nuts after a tire swap and messed a couple of them up. I now have an extended axle. If there is someone else out there that has messed up some spacers and needs some, I think I may have about 5-6 of the 8 needed in the garage. I threw the bad one out already.
Posted: Tue Mar 15, 2005 9:59 pm
by CptHook
www.radmfg.comgot my spacers there, have worked out fine for me
are you keeping the stock front width the same?
Posted: Tue Mar 15, 2005 10:43 pm
by wistech
Ive been using durablue graphite lite easy fits. They were plus 2.5" each so I threw them on the lathe and cut them down to 1.75" to get just the right width. You wont have any axle problems unless you go for huge air . Ask Sandstorm what it takes to bend a stock axle.
Posted: Tue Mar 15, 2005 11:25 pm
by acarli3
One thing about spacers is they have to fit snug up against the hub. Some of the aftermarket spacers are deep enough to do this. This severely weakens the axle at the hub bolts and can snap off if you hit hard enough from a landing or hit a tree or something.
Posted: Wed Mar 16, 2005 2:08 pm
by parks9
I have 2 inch wheel spacers on my yfz and they bent my axle! dont get them if u do motocross!
Posted: Wed Mar 16, 2005 3:03 pm
by wistech
QUOTE
Originally posted by parks9
I have 2 inch wheel spacers on my yfz and they bent my axle! dont get them if u do motocross!
I wouldnt use them on Japanese quads. The stock parts on those are to weak for spacers.
Posted: Fri Mar 18, 2005 4:56 am
by jwheat
Kevin, I had the Durablue spacers on my Dale up until January when I bought the Durablue 2+2 axle. You've seen the jumping I do and I didn't have any problems with them. If you go with wheel spacers, don't go with the type that uses individual spacers on each stud. Go with solid wheel spacers like the Durablue. The stock Cannondale axles are very durable and hard to bend.
P.S. The new map I put in screams!! I'll show you this weekend. :wow