Custom flywheel ?
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE (wistech @ Oct 4 2006, 09:43 PM) <{POST_SNAPBACK}>
Hey whatever works. Im less concerned about running out of flywheels as having it spin in the middle of nowhere. Good job.
Amen! I would hate to be approaching a big double and the quad just die on me out of nowhere. I'll be watching this project closely. Please keep us updated.
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
Just wondering. I'm not sure if this helps or not, just throwing it out there. On some of the high power cars we build we had to start double pinning the cams and on the 4.6L motors with cog blower set-ups we machine in two key ways on the crank. Not sure if this will apply to this application or not. Some of the other cool things we do is on some of the the gears in Jericos and certain engine parts we send them out to get Cryro-REM'ed. Once I get the baseline numbers down on my junk, I going to do a big cc thumper motor (don't know who yet)and was wondering about this problem. Anyways, just thought I'd put my two cents in on the subject.
Later
After looking at the flywheel some more. Cracks? Has anyone spun a flywheel up on a balancer of some sort? Cracking (if I'm not mistaken) would be cause by an imbalance, engine harmonic es, or from shear acceleration rate (trying to separate from center). I could be wrong though.
Later
After looking at the flywheel some more. Cracks? Has anyone spun a flywheel up on a balancer of some sort? Cracking (if I'm not mistaken) would be cause by an imbalance, engine harmonic es, or from shear acceleration rate (trying to separate from center). I could be wrong though.
QUOTE (promod @ Oct 10 2006, 12:28 PM) <{POST_SNAPBACK}>
Just wondering. I'm not sure if this helps or not, just throwing it out there. On some of the high power cars we build we had to start double pinning the cams and on the 4.6L motors with cog blower set-ups we machine in two key ways on the crank. Not sure if this will apply to this application or not. Some of the other cool things we do is on some of the the gears in Jericos and certain engine parts we send them out to get Cryro-REM'ed. Once I get the baseline numbers down on my junk, I going to do a big cc thumper motor (don't know who yet)and was wondering about this problem. Anyways, just thought I'd put my two cents in on the subject.
Later
After looking at the flywheel some more. Cracks? Has anyone spun a flywheel up on a balancer of some sort? Cracking (if I'm not mistaken) would be cause by an imbalance, engine harmonic es, or from shear acceleration rate (trying to separate from center). I could be wrong though.
Later
After looking at the flywheel some more. Cracks? Has anyone spun a flywheel up on a balancer of some sort? Cracking (if I'm not mistaken) would be cause by an imbalance, engine harmonic es, or from shear acceleration rate (trying to separate from center). I could be wrong though.
Pinning the flywheels seemed to ok for stock motors but the real high output strokers can rip the hub right out of the aluminum in just a couple races. The problem is the small gear cast into the center hub has way to small of teeth on them and they are not bondd to the center hub so eventually the teeth will beat the aluminum out and spin. If the gear was about an inch bigger around it might have never been an issue. Its just asking to much from a small amount of casting.
QUOTE (wistech @ Oct 10 2006, 01:45 PM) <{POST_SNAPBACK}>
Pinning the flywheels seemed to ok for stock motors but the real high output strokers can rip the hub right out of the aluminum in just a couple races. The problem is the small gear cast into the center hub has way to small of teeth on them and they are not bondd to the center hub so eventually the teeth will beat the aluminum out and spin. If the gear was about an inch bigger around it might have never been an issue. Its just asking to much from a small amount of casting.
10-4. Just throwing ideas around. Is this an issue with all stroker's no matter how you treat them or only when you beat on them?
Have ya'll looked into Cryro treating? or just due to the size it would not matter...I'll have to look at one to understand a little more.