Mydeamrides high compresion 450
Here's one with a huge gain in power from dyno tuning. Funny thing was even running ultra rich it still ran great and Mike said he was beating everything out on the lake with it. Now its got 7 more hp.LOL
The engine is a Witech ported ,stock stroke ,I believe 14.5 to 1 CP piston. Dont remember cam timing. cyclone intake 24 pound injectors,mc500 ecu, 38 pounds fuel pressure. Dont forget the Firestorm dual exhaust Mike built himself. Great job Mike.
I was a little worried you would beat my little rocket and you came sooooo close. On a side note I taught Mike how to run the dyno so we can bring lawn chairs and kick back while he tunes our quads from now on.
The engine is a Witech ported ,stock stroke ,I believe 14.5 to 1 CP piston. Dont remember cam timing. cyclone intake 24 pound injectors,mc500 ecu, 38 pounds fuel pressure. Dont forget the Firestorm dual exhaust Mike built himself. Great job Mike.
I was a little worried you would beat my little rocket and you came sooooo close. On a side note I taught Mike how to run the dyno so we can bring lawn chairs and kick back while he tunes our quads from now on.
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE (Wistech @ Mar 12 2008, 12:13 AM) <{POST_SNAPBACK}>
Here's one with a huge gain in power from dyno tuning. Funny thing was even running ultra rich it still ran great and Mike said he was beating everything out on the lake with it. Now its got 7 more hp.LOL
The engine is a Witech ported ,stock stroke ,I believe 15 to 1 CP piston. Dont remember cam timing. cyclone intake 24 pound injectors,mc500 ecu, 38 pounds fuel pressure. Dont forget the Firestorm dual exhaust Mike built himself. Great job Mike.
I was a little worried you would beat my little rocket and you came sooooo close. On a side note I taught Mike how to run the dyno so we can bring lawn chairs and kick back while he tunes our quads from now on.
The engine is a Witech ported ,stock stroke ,I believe 15 to 1 CP piston. Dont remember cam timing. cyclone intake 24 pound injectors,mc500 ecu, 38 pounds fuel pressure. Dont forget the Firestorm dual exhaust Mike built himself. Great job Mike.
I was a little worried you would beat my little rocket and you came sooooo close. On a side note I taught Mike how to run the dyno so we can bring lawn chairs and kick back while he tunes our quads from now on.
Wait till I get my bigger duals done to see if that will help with more power and we try some 22# injectors. And also try the flywheel key in the retarded position.
We set the cam timing to 110 intake and 108 exhaust. Just to bad you wouldn't let me use the bike computer for the fear of blowing my motor
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
QUOTE (cannondale27 @ Mar 12 2008, 11:41 AM) <{POST_SNAPBACK}>
Great job Mike! Did you make Wistech pay for dyno since your pipes beat his?
Of course I made him pay for the 1.5 hour dyno time when we did the exhaust battle, but I paid for the time to try to tone mine in. But the tuning is to far off this time because when I started the afr was completely off the chart (rich) from 0-redline. The bottom end is still off the chart till about 5,000 rpms, then its somewhat close.
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
Awesome job Mike. Looks like we gotta send you over a 55hp club sticker. Thats a 10hp gain from your previous motor setup. Very impressive! Also awesome job on the exhuast, almost a 4hp gain over the fmf ti pipe! You have accomplished what FMF,HMF,BIG GUN,FLOW,BILLS,AAEN, and any other professional pipe builders and big name companies couldn't do,build a true big HP pipe for a Cannondale! Your pipe looks top notch professional quality and leaves all others in the dust and makes them seem just plain weak in comparison! Yet even in your early 20's and in your 1st attempt! Can't wait to see what you big bore pipe does next. Count me in for one when you're ready to sell. I'll have a full fmf ti pipe for sale! Great job and you have talent!
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm