Almost new Cannondale Rekluse!

Message

ScramblerXLE · #1 Post by **ScramblerXLE** » Mon Sep 19, 2011 2:10 pm

Up for sale I have a Rekluse Z-Start clutch for a Cannondale. It has about 3 hours on it. I took about 2 hours to set it up in my dale, then raced it, and the engine failed (long story) had Tim rebuild it, and didn’t bother to re-install it. Then I sold it to a friend of mine this weekend (as I’m looking at getting out of Cannondales and he’s getting into them) but apparently it wasn’t designed to work with the cable clutch engines. So, we took it back out of there and it’s back in the box ready to go. This clutch usually comes with a C200L1 and a C200L2 spring. After talking to Happyboy a bit, and Rekluse a bunch, I actually wound up running a smaller diameter C150L1 spring inside of the C200L2 spring and it worked perfect. So, in one bag is the clutch as I ran it with those 2 springs. In addition, this kit will come with a C200L3 and a C150L2 for your tuning convenience

.

Since it’s low hours, and I have about $350 into it, I’d like to start there. So $350 shipped, obo.

Thanks!

//install guide for anyone interested:
http://www.rekluse.com/Cannondale_01__191-205.pdf

EDIT: I just remembered that the ball that Rekluse uses on the throw-out is a slight different size, and I don't think Tim knew that so I'm guessing that ball is still in my clutch? And my engine is back at his place again... so I'll get another one of those balls coming for whoever wants the clutch, or just knock off the cost of that little ball+shipping.

ScramblerXLE · #2 Post by **ScramblerXLE** » Sun Sep 25, 2011 4:56 am

Bump!

$310 shipped? Obo

Happyboy · #3 Post by **Happyboy** » Sun Sep 25, 2011 9:39 pm

The little ball can be replaced with the stock one. Since the hydro clutch is self adjusting it'll be fine..

ScramblerXLE · #4 Post by **ScramblerXLE** » Thu Sep 29, 2011 3:53 pm

If that's the case, it will include that.

$300 shipped until Monday. Then it will no longer be available. Let me know!

Happyboy · #5 Post by **Happyboy** » Thu Sep 29, 2011 5:59 pm

Guys, that is below cost! And way below the retail. These things are like magic when setup properly. Such an easy ride.

ScramblerXLE · #6 Post by **ScramblerXLE** » Thu Sep 29, 2011 6:10 pm

QUOTE (Happyboy @ Sep 29 2011, 01:59 PM) <{POST_SNAPBACK}>

Guys, that is below cost! And way below the retail. These things are like magic when setup properly. Such an easy ride.

Thanks Happyboy!

Below is a pic I took of the kit for anyone who may be interested.

rayspeed · #7 Post by **rayspeed** » Thu Sep 29, 2011 9:46 pm

Is all of that installable thru the clutch cover or do you need the side cover off? Sorry dont have time to look at the instructions right now but will soon.
Seriously thinking about taking that off your hands! Paypal? Where does it go on Monday?

ScramblerXLE · #8 Post by **ScramblerXLE** » Thu Sep 29, 2011 11:08 pm

Yes, it can all be installed with just the clutch cover being taken off.

Sorry man, but it looks like I just sold it. (Thanks puggi!)

I had a lower offer from a member that I was going to accept Monday if it didn't sell before then, b/c I really need the $$$ to get my dale back up and running more than I need the clutch.