Installing moto axle
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
Installing moto axle
Can someone kind of tell me what is the best way to install a axle. I saw that someone used a press to get the hubs off. What do you do if you don't have a press. Any suggestions would be appreciated.
Thanks,
Josh
Thanks,
Josh
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
Also, is the sprocket HUB on? or does it need to be put on?
the Wheel Hubs do not need to be pressed on or off. Just take off the nut (30mm or Big *** adj wrench) and they slide right off.
* i took this from a thread of mine before- if the moto axle works teh same way as the stock axle, which i believe it should..follow these steps
If you are going to be taking off a stock axle do this.
1- put quad on jack so rear end is off ground
2- Remove rear wheels and hubs.
3 - remove brake calipar and or chain along with sprocket.
4- Take stock preload nut, undo the 3 allen head bolts holding it into place. Now, this is the part im a lil not so sure about..
5 - take that and either screw it in, so the threading is threaded into the nut, loosening the axle i believe. then take out the two retaine clips underneath.
6 slide off that part, brake rotar which is connected to brake hub.
7 go to other side ( sprocket side) and pull axle on out.
the Wheel Hubs do not need to be pressed on or off. Just take off the nut (30mm or Big *** adj wrench) and they slide right off.
* i took this from a thread of mine before- if the moto axle works teh same way as the stock axle, which i believe it should..follow these steps
If you are going to be taking off a stock axle do this.
1- put quad on jack so rear end is off ground
2- Remove rear wheels and hubs.
3 - remove brake calipar and or chain along with sprocket.
4- Take stock preload nut, undo the 3 allen head bolts holding it into place. Now, this is the part im a lil not so sure about..
5 - take that and either screw it in, so the threading is threaded into the nut, loosening the axle i believe. then take out the two retaine clips underneath.
6 slide off that part, brake rotar which is connected to brake hub.
7 go to other side ( sprocket side) and pull axle on out.
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
-
- Posts: 0
- Joined: Wed Mar 10, 2021 10:41 pm
I know its an old post...
But if anyone can help with this it would be greatly appreciated.
I cannot get the axle preload nut off. I took the 3 holding screws out but that bugger is on their really good. Should this darn thing just come off with ease or what?
Gettin frustrated with it tryin to figure out how to get it off.
mike
I cannot get the axle preload nut off. I took the 3 holding screws out but that bugger is on their really good. Should this darn thing just come off with ease or what?
Gettin frustrated with it tryin to figure out how to get it off.
mike
This is nuts...
Okay so this nut will not budge. Is it possible that ATK put red loctite on this thing? I mean I weigh 245 and I am putting everything I have into it and just will not budge..
And yes I know lefty lossy right tighty. Should I torch it or is it too close to the bearing? :mad: :confused:
mike
And yes I know lefty lossy right tighty. Should I torch it or is it too close to the bearing? :mad: :confused:
mike