how would this stand?!?!

Message

440speedrider · #1 Post by **440speedrider** » Tue Nov 02, 2004 2:57 am

i was just wondering how a speed with a 2mm stoker, 450 kit, ported head with reangled injectors, some throttle body mods would stand against some modified 450s any know or some thoughts even would be good thanks fellas

speed_demon · #2 Post by **speed_demon** » Tue Nov 02, 2004 3:47 am

It wouldn't stand, it would move-right past all of the other quads!

Jaybr · #3 Post by **Jaybr** » Tue Nov 02, 2004 5:08 am

LOL, the motor you described is pretty much what Haydug and I are both running right now and it is very competetive with the other modified 450's, faster than most.

Cannondale27 and I watch Haydug hit the strait at the 12 hour behind 2 other 450's and he pulled them both for the pass at the end of the strait. I also think my quad was geared a little off and could have pulled better on top. I was running 14/38's with 18" tires and we swapped to 20" for the race and it wasn't pulling 5th as good as it could have.

Haydug also said at one point he was at WOT and a YFZ blew past him, not sure what that setup was.

cannondale27 · #4 Post by **cannondale27** » Tue Nov 02, 2004 1:05 pm

Yup Haydug went right on by even though they tried to squeeze him into the fence.Best pass I saw all day!

440speedrider · #5 Post by **440speedrider** » Tue Nov 02, 2004 2:00 pm

everyone around adams county (southern ohio, sixty miles east of cinny) has a 400 ex or a new 450 and all they 450s their their bad because they have a jet kit, exhauts and a cdi air box, im ready to way their rear ends!!

haydug · #6 Post by **haydug** » Tue Nov 02, 2004 2:25 pm

QUOTE

Originally posted by 440speedrider
everyone around adams county (southern ohio, sixty miles east of cinny) has a 400 ex or a new 450 and all they 450s their their bad because they have a jet kit, exhauts and a cdi air box, im ready to way their rear ends!!

Where are you in Ohio?? Sounds like I need to bring my dale over there. :usa

440speedrider · #7 Post by **440speedrider** » Wed Nov 03, 2004 1:10 am

im in peebles ohio, we ride at happy hollow, big rock and theirs a new one but i havnt been their yet, were r u located? come on down were a good bunch of guys just alittle compeditive, come on down and show us how its done!! Hit me back and tell me were r u located, im neer hilsobro, portsmouth, maysville, ky, mt. orab, how close are ya?

ANIMALSCANNIBAL · #8 Post by **ANIMALSCANNIBAL** » Wed Nov 03, 2004 2:42 am

I'm running 14/41 with a 465cc Timbo engine, felt like it would pull taller gearing. Tim fired up a new 465cc engine this Sunday,with 14/40 gears,,,, it's the bomb for that size. .:hammer:
Both Quads running 20" wheels. Edit>>> 20" tires

wanablaze · #9 Post by **wanablaze** » Wed Nov 03, 2004 3:36 am

20" wheels!?! So that was your bike in the "Pimp Ride" thread? J/k...

ANIMALSCANNIBAL · #10 Post by **ANIMALSCANNIBAL** » Wed Nov 03, 2004 3:48 am

QUOTE

Originally posted by wanablaze
20" wheels!?! So that was your bike in the "Pimp Ride" thread? J/k...

LoL lol I saw that,,, and no:(